How to Fill a 3 mL Injection Pen Cartridge
By Everform Pharma
Before starting, check that the empty 3 mL cartridge fits your pen, supports vented filling, and is still sealed in its packaging. Check both the peptide and BAC water vials for damage. Wash your hands and set out the equipment below.

Transfer equipment checklist
Gather these items before preparing the solution and filling the cartridge.

- Peptide powder vial. This is where you prepare the solution.
- BAC water vial. Use it if compatible with the formulation.
- Empty 3 mL glass cartridge. Check that it fits the pen and is designed for vented filling.
- Sterile transfer syringe and needle. Have a sterile syringe and needle for preparation and a fresh sterile transfer syringe and needle for filling.


- Separate sterile vent needle. Provides an outlet for displaced air.
- Alcohol wipes. For cleaning the vial stopper and cartridge seal.
- Sharps container. Keep it within reach for used needles and syringes.
Confirm the final concentration
Divide the amount of peptide in milligrams by the final solution volume in millilitres to calculate the concentration in mg/mL. The final solution volume, the amount of diluent you draw up, and the amount you transfer into the cartridge are separate measurements. Everform Pharma dosage calculator.

Prepare the solution in the powder vial
Draw the diluent from the BAC water vial and add it to the separate powder vial. Confirm that BAC water is compatible with the formulation and determine the required volume before starting. See Everform Pharma’s guide to vial preparation for more detail.
Push down1. Add air to the upright BAC water vial
Clean the rubber stoppers on both vials and let them dry. Pull back the plunger of the preparation syringe to draw in air. Keep the BAC water vial upright and insert the needle through its stopper, with the tip in the air space above the water. Push the plunger to release air into the vial. Adding air helps prevent a partial vacuum from forming as you withdraw the water.
Pull down2. Invert the vial and draw up the water
Leave the needle through the BAC water vial’s stopper and turn the vial upside down. Keep the needle tip submerged as you draw up the required amount. Check for bubbles, then read the volume at the edge of the plunger closest to the needle.
Push down3. Add the measured water to the powder vial
Turn the BAC water vial upright and withdraw the syringe. Insert the needle through the stopper of the separate powder vial. If gentle addition is appropriate for the formulation, aim toward the inside wall and press the plunger slowly. Mix using the validated method for the formulation. Inspect the vial under good lighting and check that the solution matches its expected appearance.
Fill the cartridge using a separate vent
Start with the prepared solution from Step 2 and an empty, compatible 3 mL cartridge designed for vented filling. Use a fresh sterile transfer syringe and a separate sterile vent needle. The transfer syringe carries liquid into the cartridge. The vent gives displaced air a path out as the cartridge fills.
- Prepare the cartridge. Keep it upright with the rubber seal facing up. Clean the seal and let it dry.
- Fit the vent. Seat the vent through the cartridge seal. Leave its outlet open while you fill.
- Draw up the prepared solution. Use the transfer syringe to withdraw solution from the powder vial you mixed in Step 2.
- Fill the cartridge. With the vent still in place, insert the transfer needle through the cartridge seal. Press the syringe plunger to move solution into the cartridge. Stop at the intended fill volume.
- Remove both needles. Withdraw the transfer needle and the vent, then discard the used sharps in a sharps container.

Load the filled cartridge into the pen
Seat the cartridge in its matching holder, reattach the holder to the pen body, and fit a compatible pen needle.

Clear air and check for flow
Hold the pen upright with the needle pointing straight up. Press the dose button in small increments to release the air trapped at the top of the cartridge. Stop when a drop of liquid appears at the needle tip. This is the flow check after assembly. It is separate from venting the cartridge during filling.

Remove the needle and store the pen
Remove the needle and discard it in a sharps container. Store the prepared solution under the validated conditions for that formulation. The illustration shows refrigerated storage where required.

Everform Pharma supplies peptides for laboratory research only. Everform research products must not be used for human or veterinary injection.
